Replacing uPVC Window Handles

The replacement of window handles made of upvc is an easy task. It is important to make sure that the replacement handle fits the spindle that was cut out of the window mechanism.

If you follow the steps below the handle of any cockspur will fit on most windows. The step height of the handle is important.

What to look for

A lot of windows in the UK come with uPVC handles Over time, they will begin to show signs of wear and tear. The window handle may become shaky or difficult to operate when this occurs. Anyone who is proficient using a basic hand tool can complete this relatively simple task.

The first thing to do is make sure the handle is firmly attached to the window frame, and is in a position that is open. The next step is to find the fixing pins or screws that keep the handle in place. They are usually on the inside of the handle. They can be removed with an screwdriver or pliers.

Once the handle has become loose, it can be removed from its hinges by gently pulling it off. Then, you will need to locate a replacement handle that is the same dimensions and style. This can be accomplished online or at a local DIY store, and should take five minutes using the help of a screwdriver.

One crucial aspect to take into consideration when replacing a uPVC window handle is its step height. This is the distance from the bottom of the handle to the point at which it rests on the frame of the window. This is usually a standard measurement, and it is essential that you determine the step height of your current handle before ordering the new one.

Depending on the kind of handle you choose there are various sizes that are available. Inline handles can be found for uPVC windows with lug centres of 31mm while cockspur handles come with centers of lugs of 43 millimetres. Tilt and turn handles are commonly found on uPVC windows, and they come with a unique design that allows the window to be slid up to allow for ventilation, and then turned to fully open the window.

The most frequent breakage in uPVC handles is that they crack internally instead of breaking off from the base section. This makes it difficult to open. It is important to make sure that any replacement handle is fitted with the same spindle as your original one.

Remove the old handle

Incorrectly installed or damaged window handles can cause your double glazed windows to close or open incorrectly, and can result in them getting stuck. This can be caused by many reasons, including general wear and tear on the metal handle or corrosion. In these instances, it is vital to replace the upvc window handle as promptly as you can to prevent further damage or loss of functionality.

One of the first things to do when replacing upvc window handles is to remove the old handle from the window. Start by removing the screw with the handle when it is in a closed position. This will reveal a screw that once removed, you are able to begin to remove the handle itself. It is recommended to employ an electric screwdriver to accomplish this as it will make the task much easier and quicker.

It is also worth noting that the handles' screws could be hidden behind caps made of plastic, so it is a good idea to take a Stanley knife to the screw caps and then take them off. After the handle has been removed, you must look at the square cut on the handle's base to ensure that the new window lock handles will work with it. It is crucial to measure the spindle length on the old handle and then compare it with the size of the window mechanism spindle cutout.

There are three types of Upvc handles: Espag handles with a central screw that can be turned left or right and Cranked handles that have two screws and Spade handles that have arms that are flat and can be used either side of the window made of upvc. Once you have a suitable replacement, it is simply a case of screwing the handle into place and making sure that the spindle is correctly placed into the lock mechanism. Once that is done, it should be tightened to the window frame and the replacement upvc window handles should be secure.

Take a look at the Spindle

If you need to replace a handle made of upvc that has collapsed, it's likely the spindle that holds it in place is damaged or is loose. In some cases, you can tighten the spindle by using pins or screws. In some cases, it may be necessary to replace the handle. There are many kinds of window handles made from upvc. These include inline espagnolette handles or cockspur handles. They also have tilt and turn handles. Each type has a different method for installing and replacing the handle.

It is crucial to measure the current handle prior to purchasing the replacement. This will ensure that the handle will fit the window properly and will be the right size. All handles are measured in accordance with industry standards, so it is easy to identify the correct size.

To measure the handle's size move the window to the open position. door handles repair near me should then be able to see the size of the screw or pin that is holding it. Then, use a ruler or tape measure to determine the length of the spindle. Once you have determined the length of the spindle, you can buy a new one with the same length.

The step height of a window handle is also important to take into consideration when purchasing an alternative. The step height is the distance from the bottom of the handle to the point at which it sits on the frame. Typically, this will be approximately 21mm for uPVC windows and 9mm for aluminum. Dropping something into the gap will allow you to observe how far the handle extends before it meets an obstruction.

Cockspur handles come with different backsets, based on the style of window you install them in. Inline Espag handles have the standard height of 43mm centre to centre (2 fixing points). Cockspur handles have different backsets based on the window they are in. This is because they feature a spur that extends from the handle and locks over a cockspur wedge striker plate.

Fit the New Handle

After you have chosen the new handle, ensure that it is aligned with the holes for screws on the door. Then, secure it with the screws provided. If you're also replacing the latch lever it can be put in the same way as the door handle. Then, attach the door trim again to hide the mounting screws.

Tips: To remove the metal head from the wooden wedge, hold the handle so its wider end is resting on the floor. Use a hammer to tap the thin end of the handle. Be careful not to damage the handle or spindle.